Home | Community | Message Board



Please support our sponsors.


Welcome to the Growery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Shop: Myyco.com Golden Teacher Liquid Culture For Sale   Unfolding Nature Unfolding Nature: Being in the Implicate Order   PhytoExtractum Buy Bali Kratom Powder   Kraken Kratom Red Vein Kratom

Jump to first unread post Pages: 1
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
Offlineyellownotepad
Pharmaceutical Agriculturalist
 User Gallery

Registered: 06/22/08
Posts: 1,702
Last seen: 12 years, 7 months
my tap water - analysis and how to adjust for it
    #208399 - 03/24/09 05:04 PM (15 years, 9 months ago)

so i got my tds pen, and discovered i've got 580ppm tap.  I looked up the most recent water quality report for my water district, and here's teh pertinent info:

Calcium ppm - 46
Magnesium ppm - 21

they state the average TDS for their water is 469, so my higher number may be a change on their part, or due to pipes in my house (the place is about 20 years old....is this likely?). 

i'm trying to use lucas formula with my new ebb and flow table.  for coir, i've had no problems with my tap water, but i don't have time for trial and error on teh new table.  given teh ca/mg values, and the overall tds i'm showing, should i use gh flora hardwater micro, regular micro, or soem other solution? i actually started out using floranova for the table but when i got it home and tried to use it the stuff was way too sludgy and full of crystals for me to want to deal with (and yes i shook the crap out of it).

Extras: Unfilter Print Post Top
Offlineyellownotepad
Pharmaceutical Agriculturalist
 User Gallery

Registered: 06/22/08
Posts: 1,702
Last seen: 12 years, 7 months
Re: my tap water - analysis and how to adjust for it [Re: yellownotepad]
    #208402 - 03/24/09 05:09 PM (15 years, 9 months ago)

more info:  according to gh if your calcium ppm is 30-50, they recommend a mix of hardwater micro and regular micro to accomodate.  however they also say to use hardwater micro with tap water that is >200ppm TDS or >70ppm Ca.  I have 580ppm TDS but only 46ppm Ca.  Any expert advice would be awesome, i've been googling the crap out of this and haven't found an answer that makes me comfortable yet.

Extras: Unfilter Print Post Top
Offlineyellownotepad
Pharmaceutical Agriculturalist
 User Gallery

Registered: 06/22/08
Posts: 1,702
Last seen: 12 years, 7 months
Re: my tap water - analysis and how to adjust for it [Re: travelleler]
    #208758 - 03/25/09 02:33 PM (15 years, 9 months ago)

alright well so far no answers, but i'm doing the math myself and posting here for others who may run into this sort of thing

the lucas formula's veg is 5ml micro and 10ml bloom, assuming 0ppm starting point (R/O water).

that yields this profile:
Nitrogen(n) - 62
Nitrogen(a) - 3
Nitrogen(u) - 0
Phosphorous - 62
Potassium  - 100
Calcium    - 67
Magnesium  - 39
Sulfur      - 52
Iron        - 1.5
Manganese  - 0.6
Zinc        - 0.1
Copper      - 0.1
Boron      - 0
Molybdenum  - 0.01
Cobalt      - 0.01

a little more detail on my tap water, here's all the elements that i am factoring in here (all in ppm, except boron, which is parts per billion)

Calcium    - 46
Boron      - 140 ppB
Potassium  - 3.9
Magnesium  - 21

so based on these figures, if i mixed  a lucas formula up using my tap but not checking on my water quality, i'd have 68.7% too much calcium, 3.9% too much potassium, 53.8% too much magnesium.  The potassium is acceptable, and the boron is negligible.  Everything else in the detailed water analysis is not listed in standard nutrient profiles, and so i'm leaving it out.  The thing to see here is that while my tap water tastes normal, looks normal, and is generally good quality, it would most likely cause me some problems.  However with that being said, I've been using my tap water in coir and it's worked great due to the way coir is.


So in order to adjust, if i were to switch to hardwater micro, and keep the same amounts, i'd have the following profile for the nutrients:

Nitrogen(n) - 48
Nitrogen(a) - 3
Nitrogen(u) - 13
Phosphorous - 62
Potassium  - 100
Calcium    - 71
Magnesium  - 50
Sulfur      - 52
Iron        - 1.5
Manganese  - 0.6
Zinc        - 0.1
Copper      - 0.1
Boron      - 0
Molybdenum  - 0.0240
Cobalt      - 0

the changes with hardwater micro are that the overall nitrogen is raised by 2ppm (negligible 3.2% boost), but some is from urea which is absent in regular micro, cobalt is absent, calcium is reduced from 67 to 14 ppm (79.1% reduction). 


If you take the profile where hardwater micro is used, and add in my particular tap water analysis, we can gather the following:

-my new calcium content is 60ppm.  this is 7ppm (10.5%) less than ideal.

-my new nitrogen content is 64ppm.  this is 2ppm (3.2%) more than ideal

-my new potassium content is 103.9ppm.  this is 3.9ppm (3.9%) more than ideal

So we can see, using hardwater micro in the same ratio would make my overall nutrient profile much closer to ideal.  It doesn't fix the overabundance of magnesium, but does reduce the calcium problem from being nearly 70% too much, to being 10% too little.  I'm not sure how to deal with the extra magnesium, short of using a chemical process to precipitate it out.

If i wanted to be slightly more tricky, I could also use a combination of regular micro and hardwater micro to get the ideal calcium content (21 ppm from nutrients, 46ppm from the water).

The closest to ideal that I care to find right now is by using 1ml micro, 4ml hardwater micro, and 10ml bloom.  That gets me to the following profile when my water's analysis is factored in:


Nitrogen(n) - 51
Nitrogen(a) - 3
Nitrogen(u) - 19
Phosphorous - 62
Potassium  - 100
Calcium    - 25
Magnesium  - 39
Sulfur      - 52
Iron        - 1.5
Manganese  - 0.6
Zinc        - 0.1
Copper      - 0.1
Boron      - 0
Molybdenum  - 0.01
Cobalt      - 0

:strokebeard:

Extras: Unfilter Print Post Top
Offlineyellownotepad
Pharmaceutical Agriculturalist
 User Gallery

Registered: 06/22/08
Posts: 1,702
Last seen: 12 years, 7 months
Re: my tap water - analysis and how to adjust for it [Re: Dr. Penguin]
    #209093 - 03/26/09 10:58 AM (15 years, 9 months ago)

sodium is 83ppm.  also keep in mind the water district states the water is 469ppm, so my higher reading most likely includes elements from the plumbing in my house i guess..?

Extras: Unfilter Print Post Top
Jump to top Pages: 1

Shop: Myyco.com Golden Teacher Liquid Culture For Sale   Unfolding Nature Unfolding Nature: Being in the Implicate Order   PhytoExtractum Buy Bali Kratom Powder   Kraken Kratom Red Vein Kratom


Similar ThreadsPosterViewsRepliesLast post
* pH adjusters + organics = ? impgl 4,975 8 08/13/08 12:58 PM
by impgl
* pH adjusters and EC... Dr. Awesome 2,117 4 04/05/09 03:03 PM
by Dr. Penguin
* Tap Water icanfeeltherain 1,705 4 03/30/09 08:44 AM
by bobby
* Organic Soil Mixes
( 1 2 all )
dumbfounded1800 20,182 26 08/30/09 06:12 PM
by djstan627
* Lowering or Raising PH KaptKid 3,010 10 04/04/09 03:01 PM
by Harry_Ba11sach
* EZ-Clone test. MagashM 8,028 16 11/09/08 10:27 PM
by FurrowedBrow
* sex reversal with colloidal silver *DELETED* FrozenReality 2,943 2 09/17/08 06:45 PM
by FrozenReality
* want to improve grow tony8404 2,755 5 04/23/09 08:20 AM
by Dr. Penguin

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: FurrowedBrow, Magash, Data, Dr. Siekadellyk, phychotron
3,382 topic views. 0 members, 994 guests and 55 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ]
Search this thread:
Original Seeds Store
Please support our sponsors.

Copyright 1997-2025 Mind Media. Some rights reserved.

Generated in 0.027 seconds spending 0.01 seconds on 16 queries.