Welcome to the Growery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!
|
 Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
|
 double
Diesel
Registered: 02/12/11
Posts: 207
|
 Plant material extraction questions 
#596215 - 11/08/11 02:16 PM (13 years, 27 days ago) |
|
|
Hello,
did anybody here perform a chloroform extraction of plant material? Would there be any way to condense solvent thus allowing to be reused?
Reading around it seems like chloroform would be the best solvent for THC extraction since it doesn't dissolve waxes and chlorophyll and it doesn't mix with water.
How would this compare to a ice hash extraction difficulty- and yield-wise?
Thank you
|
double
Diesel
Registered: 02/12/11
Posts: 207
|
Re: Plant material extraction questions [Re: double]
#597700 - 11/20/11 10:59 AM (13 years, 15 days ago) |
|
|
Nobody?
Ok, so a different question:
would extracting plant material with say acetone, evaporating everything and then dissolving that sticky mess (due to chlorophyll and waxes dissolved by acetone or alcohol) in a smaller amount of chloroform yield a purified material while requiring less high-end solvent due to pre-processing with a cheap one?
Would chilling that first all-around solvent to 15°F make any difference?
Thank you
|
 RasJeph
Psycho Pete
Registered: 01/14/09
Posts: 11,657
Loc: Bumfuckt Egypt
Last seen: 1 year, 30 days
|
Re: Plant material extraction questions [Re: double]
#597822 - 11/21/11 07:21 AM (13 years, 15 days ago) |
|
|
If you freeze your bud/shake before hand to get the trichs brittle and ready to fall off, AND use cold iso, AND only shake it around (I swirl it actually) for 30 seconds, you hardly pull out anything you don't want. I had my iso dry up white once, I was so confused. It was just cloudy trichs and a real good extraction.
And of course any consecutive washes will result in a more pure end result...but its not needed at all.
--------------------
Of course it's happening inside your head.
Why should that mean it isn't real?
|
double
Diesel
Registered: 02/12/11
Posts: 207
|
Re: Plant material extraction questions [Re: RasJeph]
#597855 - 11/21/11 12:28 PM (13 years, 14 days ago) |
|
|
Quote:
RasJeph said:
If you freeze your bud/shake before hand to get the trichs brittle and ready to fall off, AND use cold iso, AND only shake it around (I swirl it actually) for 30 seconds, you hardly pull out anything you don't want. I had my iso dry up white once, I was so confused. It was just cloudy trichs and a real good extraction.
And of course any consecutive washes will result in a more pure end result...but its not needed at all.
I guess getting other stuff dissolved won't be an issue if you let it dry then redissolve in a more selective solvent (chloroform). also by letting plant material soak for longer than 30 seconds, won't it draw more THC in solution too?
My question was if, given that solvent extraction have better yields than say bubble hash etc., would it have been feasible to dissolve about everything in acetone (soaking for some hours) then evaporating, then redissolving that junk mix in a more selective and costly solvent like chloroform, which should be the best for THC extraction.
|
P-O
Registered: 10/08/11
Posts: 17,891
|
Re: Plant material extraction questions [Re: double]
#597937 - 11/22/11 02:32 AM (13 years, 14 days ago) |
|
|
I dont know anyone who has used chloroform for a extraction. w
ould it evaporate without any residue? If so let us know how the extraction goes...
imo... iso oil< butane oil < bubble hash...
|
DudeTron
Registered: 10/24/09
Posts: 407
Last seen: 10 years, 10 months
|
Re: Plant material extraction questions [Re: P-O]
#598029 - 11/22/11 01:40 PM (13 years, 13 days ago) |
|
|
I was researching some some of the chemicals in 'contact cleaner' trying to determine if it would be safe and effective as a mostly Hexane based extraction...
Anyway I came across this intense chemistry article specific to extraction of cannibinoids and hemp chemicals...
Quote:
6.2 Extraction ~
Chloroform is the most efficient solvent for the extraction of THC from cannabis. A single extraction will remove 98-99% of the cannabinoids within 30 minutes. A second extraction removes only 88-99% of the cannabinoids within 30 minutes. A second extraction removes 100% of the THC.
|
double
Diesel
Registered: 02/12/11
Posts: 207
|
Re: Plant material extraction questions [Re: DudeTron]
#598505 - 11/26/11 05:04 AM (13 years, 10 days ago) |
|
|
Thank you. I thought that first extraction with a cheap solven would have reduced overall purification mass for a dipping in chloroform
| |
|
|
 |
|
using plant material after dry sift |
 RasJeph |
2,320 |
1 |
05/16/11 06:46 PM
by Psuper | |
|
extraction question |
 mandini |
3,959 |
7 |
02/15/09 11:49 AM
by SpaceMonkey | |
|
Glass BHO Extraction Tube: Product Review
(  1 2 all ) |
 coda |
33,423 |
27 |
04/28/11 03:35 PM
by spencaman01 | |
 |
Easy Butane Extraction |
 Dr. Penguin |
35,437 |
10 |
08/04/09 12:15 AM
by Ero42oH2o | |
|
using solvent after bubble bags |
shags420 |
2,249 |
3 |
01/10/10 01:53 AM
by coda | |
 |
Jar Hash - Quick and easy ice extraction |
 aspore |
15,706 |
2 |
11/17/10 02:45 PM
by DoctorDarkMatter | |
|
Butane honey oil, dried/cured plant, or fresh work? |
suchsmartmonkeys |
3,927 |
3 |
01/20/10 11:33 AM
by SmOakland | |
|
Couple questions on oil |
 Chronica |
6,421 |
15 |
07/21/11 08:47 AM
by HGH |
|
|
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Magash, Data
5,077 topic views. 0 members, 49 guests and 143 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ] | | |
|
|
|
Threaded
Previous
Index
Next
Edit 
Reply 
