Quote:

---

TrippyShitMan said:
hahah your still ranting get over it harry....sad. i could give 2 fucks less about spelling on a forum lets not drag this of topic! Roll Joints peps!!!!!

---

Alright fine, I rolled one just for you. At least as good as yours (but actually better, because I left the mouthpiece wide enough to actually let smoke through).

Notice how long this takes, and herein lies my argument;

Since the competition is best joint ROLLER on the growery, not best JOINT, then time matters. you can roll amazing joints, but if it takes you longer than 5 minutes, you're not a good joint ROLLER. Understand where I'm coming from here? You think I'm just picking on you, but I'm actually merely trying to enforce the implied rules due to the name of the contest.

With that said, here's my official submission. this took less than 2 minutes total, and is exactly the same density at every point. I'll post a video of it being smoked if you guys want proof that it doesn't boat or run at any point.

Quote:

---

Harry_Ba11sach said:

Quote:

---

TrippyShitMan said:
hahah your still ranting get over it harry....sad. i could give 2 fucks less about spelling on a forum lets not drag this of topic! Roll Joints peps!!!!!

---

Alright fine, I rolled one just for you. At least as good as yours (but actually better, because I left the mouthpiece wide enough to actually let smoke through).

Notice how long this takes, and herein lies my argument;

Since the competition is best joint ROLLER on the growery, not best JOINT, then time matters. you can roll amazing joints, but if it takes you longer than 5 minutes, you're not a good joint ROLLER. Understand where I'm coming from here? You think I'm just picking on you, but I'm actually merely trying to enforce the implied rules due to the name of the contest.

With that said, here's my official submission. this took less than 2 minutes total, and is exactly the same density at every point. I'll post a video of it being smoked if you guys want proof that it doesn't boat or run at any point.

---

Yeah, i should have clarified that.  I knew i'd fuck it up somehow.    Thanks for your submission.

Quote:

---

geokills said:
That's exactly what I do... I typically have a 3" x 5" note card laying around and cut out a rectangular strip that's about 4 or 5 times as long as it is wide.  Then I bend it up /\/\/\/\/ (without creasing) and lightly compress it to slide it into the end of a finished joint.  It should fit in the joint so that there is still 1 - 2 mm of joint paper overhang.  As you postulated, the springiness will allow for easy placement and also to keep it in place.  For added security, twist closed the lighter-end of the joint and take a draw on the sealed product to "fit" the joint paper snugly around the accordion.

There are a several reasons I do this:

• It keeps the mouth-side of the joint open for solid smoke-flow regardless of sloppy smokers or tar build up.
  
• It acts as a stop on the end of the joint to prevent any weed from falling through (as may happen with an open "C" crutch).
  
• It allows the smoker to finish all the weed without having to worry much about burning their fingers or using a roach clip.
  
• It is durable, will not fall out (when implemented appropriately), and is resistant to being crushed.

---

i never use a roach but i might give that a shot.  seeing as i lost my hemostats

not a bad idea at all.  i've also never heard it called a crutch.  must be some kinda cali thing.  infact, i think i know one person here that uses them.

dont get me wrong, i have used them before.  i remember once DSG was smoking the roaches in my ashtray and he tried to light one that had a tip in it, he sucked the flame straight through the little tube and into his mouth.  that deterred him from further smoking my roaches